TEST AR SER

Armory Services

Don’t live in our area but still want to use our Armory Services? You can ship your firearm to us.

Service Charges & Terms

We reserve the right to refuse any work that our armorer deems would make the firearm unsafe.
We will not remove or disconnect any firearm safety and/or any component that would cause the firearm to violate federal and/or state laws.
Service prices do not include parts or materials.
Service prices are subject to change depending on the difficulty of the job.

Service	Description	Price
Hourly Rate – Man Hours	Armorer labor only	$150
Hourly Rate – Man / Machine Hours	Armorer plus machine time	$175
Minimum Charge per Firearm	Applied to any firearm brought in	$20
Written Cost Estimate	Free if we perform the work	$40

General Armory Services

Service	Notes
Barrel Inspection (Borescope)	.20 caliber and above only
Chamber Cast	Evaluate chamber dimensions and condition
Clean & Inspect – Revolvers / Pistols	Full cleaning and safety inspection
Clean & Inspect – Rifles / Shotguns	Full cleaning and safety inspection
Drill & Tap – Aluminum / Steel	Standard metals
Drill & Tap – Hardened Metal	Includes additional setup for hardened materials
Lap Bore	Improve consistency and smoothness of bore
Muzzle Device Install (Pre-threaded Barrel)	Install muzzle brake / flash hider / similar
Muzzle Device – Pin / Weld	Permanent attachment to meet legal length requirements
Polish Chamber	Reduce roughness and improve extraction
Remove Stuck Case / Bore Obstruction	Safe removal of stuck case or obstruction
Throat & Feed Ramp Polish	Improves feeding reliability

AR-10 / AR-15 Services

*Price is determined by difficulty of disassembly/reassembly.

Service	Notes
Assemble – Upper	Complete upper assembly
Assemble – Lower	Complete lower assembly
Assemble – Complete Rifle	Full AR-10 / AR-15 build
Cut / Polish Feed Ramps	Enhance feed path smoothness
Dimple Barrel for Gas Block	Add $40 for disassemble/reassemble
Install Gas Block & Dimple Barrel	Install and align gas block with barrel dimpling
Install Rear Sling Plate	Sling attachment at lower grip / buffer tube area
Install Trigger	Standard or drop-in AR trigger installation
Replace Gas Rings	Bolt carrier group gas ring replacement
Replace Gas Tube	Remove and install new gas tube
Replace Buffer Tube	Receiver extension / buffer tube replacement
Stake Castle Nut	Proper staking to secure castle nut

Finishing

*Price is determined by number of parts.

Service	Notes
Abrasive / Bead Blast / Wire Wheel (Matte)	Surface prep for uniform matte finish
Deluxe Finish – Handguns	Hand sanding up to 400 grit
Deluxe Finish – Rifles / Shotguns	Hand sanding up to 400 grit
Draw Filing	Precision surface leveling and clean-up
Parkerize – Manganese – Handguns	Includes metal prep
Parkerize – Manganese – Rifles / Shotguns	Includes metal prep
Slow Rust Bluing – Handguns	Includes metal prep
Slow Rust Bluing – Rifles / Shotguns	Includes metal prep

Trigger Work

Service	Notes
Trigger Kit Installation (Drop-In)	Additional cost if inletting required
Trigger Job – Revolvers	Smooth & tune
Trigger Job – Semi-Auto Pistols	Smooth & tune
Trigger Job – Rifles	Smooth & tune
Trigger Pull Reduction / Spring Kit Installation	Adjust pull weight with appropriate springs

Sight Work

Service	Notes
Bore Sighting – Standard Scopes w/ Collimator	Simulates 100 yards for initial sight-in
Front Sight Ramp – Screw-On (Drill & Tap)	Install ramp front sight
Remove / Install – Dovetail	Front or rear dovetail sight
Remove / Install – Staked	Staked front sight removal / install
Remove / Install – M1 Carbine (Front / Rear)	Front or rear sight install on M1 Carbine
Scope Mounting	Lap rings, mount scope, and boresight
Shotgun Bead – Front / Mid (Drill & Tap)	Install or replace shotgun bead sight

Stock Work

*Price is determined by complexity of stock.

Service	Notes
Clean & Oil Finish – Hand Rubbed (Unfilled Grain)	Hand-rubbed oil finish with open grain
Clean & Oil Finish – Hand Rubbed (Filled Grain)	Hand-rubbed oil finish with filled grain
Complete Refinishing	Sand, stain, raise dents, oil
Inlet / Fit Stock	Fit stock to action and hardware
Recoil Pad Installation – Grind-to-Fit	Fit and finish recoil pad to stock
Recoil Pad Installation – Standard	Add $40 if drilling required
Sling Swivel Installation (Drill Stock)	Install sling studs / swivels

Machine Work

Service	Notes	Price
Barrel Threading	Thread barrel for muzzle device or suppressor	$175
Milling – Hourly Rate (Machine)	Machine time for custom cuts / milling	Contact for quote

Please contact us about any service not listed above.

How to Ship Your Firearm

Before you ship, contact us so we can confirm details and current turnaround times.

Include your contact information, phone number, email, and return shipping address inside the box, along with a copy of your driver’s license (or FFL, if applicable). Make sure the firearm is unloaded and packed securely.